View CXA1100_125280.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CXA1100P, CXA1101P/M, CXA1102P/M, CXA1163P/M
Dolby B Type Noise Reduction System For the availability of this product, please contact the sales office.
Description CXA1100, CXA1101, CXA1102 and CXA1163 are ICs including two separate Dolby B type noise reduction processors. Seven devices with four Dolby levels and two types of package are provided for various applications. These devices feature very few external components, which is achieved by integrated filter circuits using integrated thin film capacitors with high capacitance. Features * Minimum number of external components * NR ON/OFF and REC/PB switchs included * Small package (DIP16, SOP16) ~ * Small supply current (--5.5mA, Typ.) * Dual channel processors in one chip Absolute Maximum Ratings (Ta = 25C) * Supply voltage VCC 17 V * Operating temperature Topr -30 to +85 C * Storage temperature Tstg -55 to +150 C * Allowable power dissipation PD DIP16 (A1100P/A1101P/A1102P/A1163P)900 mW SOP16 (A1101M/A1102M/A1163M) 500 mW Note 1) These ICs are available only to the licensees of Dolby Laboratories Licensing Corporation from whom licensing and application information may be obtaind. Note 2) "Dolby" and double D symbols are trade marks of Dolby Laboratories Licensing Corporation. 16 pin DIP (Plastic) 16 pin SOP (Plastic)
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
-1-
E90302A13-PP
CXA1100/CXA1101/CXA1102/CXA1163
Pin Description No. Symbol Z (in) VDC
(Ta = 25C, VCC = 12V (Single supply), No signal) Equivalent Circuit
Vcc
Description
1, 16
REC IN
40k
6.0V
1 16 40k Vcc/2 GND
Recording (Encode) input
2
VCC
--
12.0V
Vcc
Power supply
3, 14
PB IN
40k
6.0V
3 14 40k Vcc/2 GND
Playback (Decode) input
4
VCC/2
1k
6.0V
Vcc 50 150
Single supply VCC/2 Split supply Ground
Mode control pin for NR ON/OFF 5 ON/OFF -- --
5
"H" NR OFF "L" NR ON
GND Vcc
150
6, 11
LINE OUT
--
6.0V
6 11 150
Line (Decode) output
GND
-2-
CXA1100/CXA1101/CXA1102/CXA1163
No.
Symbol
Z (in)
VDC
Equivalent Circuit
Vcc
Description
4 8.2k
7, 10
TC
--
0.3V
7 10 100k
Time constant pin for the level detector
GND Vcc
300
8, 9
REC OUT
--
6.0V
8.2k 8 9 300
Recording (Encode) output
GND Vcc 50 150
12
REC/PB
--
--
12
Mode control pin for REC/PB (Encode/Decode) "H" B (Decode) "L EC (Encode)
GND Vcc
13
IREF
--
1.2V
13
1.2V
Reference current input pin for the active filters
10 GND
15
GND
--
0V
Single supply Ground Split supply VEE
-3-
CXA1100/CXA1101/CXA1102/CXA1163
Block Diagram
C12 1 PB IN REC IN C11 1 16 15 14 13
REC/PB C14 4.7 LINE OUT R1 43k 12 11 10 C13 0.68 9 C15 4.7 REC OUT
ATT1 SC ATT2 ATT3 ATT3 ATT2 SC ATT1 ATT3 DET DET
C21 1 REC IN PB IN C22 1
1
2
3
4 C1 100
5
6
7 C23 0.68
8
C25 4.7 REC OUT
LINE OUT C24 4.7 Vcc ON/OFF ATT: Attenuator SC : Side Chain DET: Detector
Test Circuit
S3
P R OFF R11 5.1k
R12 5.1k C12 1 C11 1 R1 43k 13 12 11 C13 C14 0.68 4.7 10 9
P R
S5-1
C16 4.7 1 2 S6-2
DC Level Meter R2 10k CCIR/ARM Filter
Audio SG
16
15
14
1 1 Vcc 2 3 4 5 6 7 8 C23 0.68 R P 2 C25 4.7 S5-2 S6-1 C1 C22 100 C24 C2 1 4.7 100 S2 OFF ON R5 R3 R4 12k 510 2k P R S1
OFF
ON S7
A
R21 R 5.1k OFF S4 P C21 1 R22 5.1k
AC Level Meter Distortion Analyzer
+15V
-4-
CXA1100/CXA1101/CXA1102/CXA1163
Electrical Characteristics
Ta = 25C, Dolby Level: -10dBm ( = 245mVrms) at REC OUT VCC = 15V (CXA1100), VCC = 12V (CXA1101), VCC = 9V (CXA1102) VCC = 6V (CXA1163) Test Condition R/P -- NR -- f (Hz) Other Conditions -- Signal Handling 12dB Min. Typ. Max. Unit
Item Operating voltage CXA1100 CXA1101 CXA1102 CXA1163 Supply current CXA1100 CXA1101 CXA1102 CXA1163 LINE OUT level CXA1100 CXA1101 CXA1102 CXA1163 REC IN level PB IN level Encode characteristics (Boost) (1) (2) (3) (4) (5) Signal handling CXA1100 CXA1101 CXA1102 CXA1163
Symbol Vopr
11.5 8.5 6.5 5.0 3.5 3.5 3.5 3.5
-- -- -- -- 5.6 5.5 5.3 5.1 0.0 -3.0 -6.0 -10.0 -30 -30
16.0 16.0 16.0 16.0 7.5 7.5 7.5 7.5 1.0 -2.0 -5.0 -9.0 -28 -28
V V V V mA mA mA mA dBm dBm dBm dBm dBm dBm
ICC
R
OFF
--
No signal
Vlout
R
OFF
1k -1.0 -4.0 -7.0 -11.0
Vrin Vpin
R P
OFF OFF
1k 1k
-32 -32
B-R-1 B-R-2 B-R-3 B-R-4 B-R-5 Vomax
R R R R R R
ON ON ON ON ON OFF
500 2k 5k 10k 10k 1k
-25dB -25dB -25dB -40dB 0dB THD = 1%
1.4 5.5 3.9 9.7 -1.1 13.5 14.0 14.0 13.0
2.9 7.0 5.4 10.4 0.4 15.3 15.9 15.9 15.0
4.4 8.5 6.9 11.9 1.9 -- -- -- --
dB dB dB dB dB dB dB dB dB
0dBm = 0.775Vrms
-5-
CXA1100/CXA1101/CXA1102/CXA1163
Item Total harmonic distortion 1) NR OFF CXA1100 CXA1101 CXA1102 CXA1163 2) NR ON CXA1100 CXA1101 CXA1102 CXA1163 Input impedance REC IN PB IN Encode S/N ratio Crosstalk REC-PB PB-REC REC ch to ch PB ch to ch REC OUT Offset voltage (NR ON -- OFF) Control voltage "H" Level "L" Level
Symbol
Test Condition R/P NR f (Hz) Other Conditions
Min.
Typ.
Max.
Unit
THD (OFF)
R
OFF
1k
+10dB -- -- -- -- 0.03 0.04 0.05 0.06 0.03 0.04 0.06 0.09 40 40 69 0.2 0.2 0.2 0.2 0.3 0.3 0.3 0.3 57 57 -- % % % % % % % % k k dB
THD (ON)
R
ON
1k
+10dB -- -- -- --
Zrec Zpb SN (CCIR) CT-1 CT-2 CT-3 CT-4 Voff
-- -- R
-- -- ON
1k 1k -- Rg = 5k (CCIR/ARM) 0dB 0dB 0dB 0dB
28 28 65
P R R P R
OFF OFF OFF OFF ON
1k 1k 1k 1k --
-- -- -- -- -40
-82 -81 -70 -70 0
-65 -60 -60 -60 40
dB dB dB dB mV
VC-H VC-L
-- --
-- --
-- --
2.5 0
-- --
VCC 0.5
V V
0dB means the level which provides the Dolby level at the recording output in the noise reduction off mode.
-6-
CXA1100/CXA1101/CXA1102/CXA1163
Example of Representative Characteristics
Quiescent Current vs. Supply Voltage Supply Current vs. Input Voltage (CXA1101)
Encode Mode 0dB = Dolby Level
6.0
6.8
Icc -- Quiescent current [mA]
5.6 5.2 4.8 NR ON 4.4 4.0 3.6 4 6 8 10 12 14 16 NR OFF
Icc -- Supply current [mA]
6.4 6.0 5.6 NR OFF 1kHz, 10kHz 5.2 4.8 4.4 -12 NR ON 10kHz NR ON 1kHz -8 -4 0 4 8 12
Vcc -- Supply voltage [V]
Input level [dB]
Encode Characteristics
VCC = 12V 12 -50dB 10 12 10
Temperature Characteristics
VCC = 12V Ta = -25C Ta = 25C Ta = 75C -40dB
Encode boost [dB]
8 6 4 2 0 200 500 1k 2k
Encode boost [dB]
-40dB -30dB
8 6 4 2 0
-30dB
-20dB -10dB 0dB 5k 10k 20k
-20dB -10dB 0dB 5k 10k 20k
200
500
1k
2k
Frequency [Hz]
Frequency [Hz]
Signal Handling
Encode Mode 20 NR OFF f = 1kHz THD = 1% 18 16 14 12 10 8 4 6 8 10 12 14 16 0 1 A1163 A1102 A1101 A1100
Load Characteristics (CXA1101)
Encode Mode 14 VCC = 12V THD = 1% 12 10 8 REC OUT 6 4 2 LINE OUT
Maximum output level [dBm]
Signal handling [dB]
2
3
4
5
6
7
Vcc -- Supply voltage [V]
RL -- Load resistance [k]
-7-
CXA1100/CXA1101/CXA1102/CXA1163
NR off Tot al Harrmonic Dist ort ion-1 (CX A1101)
1.0 Encode Mode VCC = 12V 0dB = Dolby Level 1.0
NR onTot al Harrmonic Dist ort ion-1 (CX A1101)
Encode Mode VCC = 12V 0dB = Dolby Level
Total Harmonic Disttortion [%]
Total Harmonic Disttortion [%]
0.5
0.5
0.2 0.1 0.05
0.2 0.1 0.05
0.02 0.01 -8 -4 0 4 8 f = 100Hz f = 1kHz f = 10kHz 12 16
0.02 0.01 -8 -4 0 4 8 Output Level [dB] f = 100Hz f = 1kHz f = 10kHz 12 16
Output Level [dB]
NR off Tot al Harrmonic Dist ort ion-2 (CX A1100)
1.0 0.5 Encode Mode 0dB = Dolby Level f = 1kHz 1.0
NR onTot al Harrmonic Dist ort ion-2 (CX A1100)
Encode Mode 0dB = Dolby Level f = 1kHz
Total Harmonic Disttortion [%]
Total Harmonic Disttortion [%]
0.5
0.2 0.1 0.05
0.2 0.1 0.05
0.02 0.01 -8 -4 0 4 8 VCC = 15V VCC = 11.5V 12 16
0.02 0.01 -8 -4 0 4 8 Output Level [dB] VCC = 15V VCC = 11.5V 12 16
Output Level [dB]
NR off Tot al Harrmonic Dist ort ion-3 (CX A1101)
1.0 Encode Mode 0dB = Dolby Level f = 1kHz 1.0
NR onTot al Harrmonic Dist ort ion-3 (CX A1101)
Encode Mode 0dB = Dolby Level f = 1kHz
Total Harmonic Disttortion [%]
0.5
Total Harmonic Disttortion [%]
VCC = 15V VCC = 12V VCC = 8.5V
0.5
0.2 0.1 0.05
0.2 0.1 0.05
0.02 0.01 -8 -4 0 4 8
0.02 0.01 -8 -4 0 4 8 VCC = 15V VCC = 12V VCC = 8.5V 12 16
12
16
Output Level [dB]
Output Level [dB]
-8-
CXA1100/CXA1101/CXA1102/CXA1163
NR off Tot al Harmonic Dist ort ion-4 (CX A1102)
1.0 Encode Mode 0dB = Dolby Level f = 1kHz 1.0 0.5
NR on Tot al Harmonic Dist ort ion-4 (CX A1102)
Encode Mode 0dB = Dolby Level f = 1kHz
Total Harmonic Distortion [%]
Total Harmonic Distortion [%]
0.5
0.2 0.1 0.05
0.2 0.1 0.05
0.02 0.01 -4 0 4 8 12 VCC = 15V VCC = 9V VCC = 6.5V 16 20
0.02 0.01 -4 0 4 8 12 Output Level [dB] VCC = 15V VCC = 9V VCC = 6.5V 16 20
Output Level [dB]
NR off Tot al Harmonic Dist ort ion-5 (CX A1163)
1.0 1.0
NR on Tot al Harmonic Dist ort ion-5 (CX A1163)
Total Harmonic Distortion [%]
Total Harmonic Distortion [%]
0.5
Encode Mode 0dB = Dolby Level f = 1kHz
0.5
Encode Mode 0dB = Dolby Level f = 1kHz
0.2 0.1 0.05
0.2 0.1 0.05
0.02 0.01 0 4 8 12 16 VCC = 15V VCC = 6V VCC = 5V 20 24
0.02 0.01 0 4 8 12 16 VCC = 15V VCC = 6V VCC = 5V 20 24
Output Level [dB]
Output Level [dB]
Channe l t o Channe l Crosst alk (CX A1101)
-30 -40 -50 VCC = 12V/6V NR off C1 (Pin4) = 100F -30 -40 -50 -60 -70 -80 -90
REC t o PB and PB t o REC Crosst alk (CX A1101)
VCC = 12V/6V NR off C1 (Pin4) = 100F
Crosstalk [dB]
-60 -70
Single Supply Split Supply
Encode Decode
Crosstalk [dB]
Single Supply
-80 -90
Split Supply 100 200 500 1k 2k Frequency [Hz] 5k 10k
100
200
500
1k
2k
5k
10k
Frequency [Hz]
-9-
CXA1100/CXA1101/CXA1102/CXA1163
Ripple Rejection Ratio-1 (CXA1101)
Encode Mode VCC = 12V Single Supply
Ripple Rejection Ratio-2 (CXA1101)
Decode Mode VCC = 12V Single Supply C1 (Pin4) = 100F -20 C1 (Pin4) = 470F -30 -40 NR on -50 NR off -60 -70
-10
-10
Ripple rejection ratio [dB]
-20 C1 (Pin4) = 100F -30 -40 -50 NR off -60 -70 100 200 500 1k 2k 5k 10k NR on C1 (Pin4) = 470F
Ripple rejection ratio [dB]
100 200
500
1k
2k
5k
10k
Frequency [Hz]
Frequency [Hz]
Ripple Rejection Ratio-3 (CXA1101)
VCC Rejection VCC, VEE = 6V
Ripple Rejection Ratio-4 (CXA1101)
-10
0
NR on
Ripple rejection ratio [dB]
Ripple rejection ratio [dB]
-20 -30 -40 NR on -50 NR off -60 -70 100 200 500 1k 2k 5k 10k Encode Decode
-10 -20 -30 -40 -50 -60 100 200 500 1k 2k 5k 10k VEE Rejection VCC, VEE = 6V Encode Decode
NR off
Frequency [Hz]
Frequency [Hz]
Notes on Applications 1) Power supply The CXA1100 Series is basically designed to operate on single ended supply. The split supply operation is also possible, however, VEE (negative) supply should provide low noise and ripple characteristics. The ripple rejection ratio of these devices is generally good for Vcc supply (single ended supply and split supply), however, that for VEE supply is not so good in the NR on mode because the integrated capacitors for the side chain filter are connected to pin 15 (VEE on split supply).
- 10 -
CXA1100/CXA1101/CXA1102/CXA1163
When the ripple or noise component of VEE supply is not negligible small, the CR filter shown in Fig. a-1 will be usefull.
R1 43k
The operation voltage range are CXA1100 11.5 to 16V (5.75 to 8V) CXA1101 8.5 to 16V (4.25 to 8V) CXA1102 6.5 to 16V (3.25 to 8V) CXA1163 5.0 to 16V (2.5 to 8V)
13 14 47 VEE 100 to 470F 15 CXA1100 Series
Fig. a-1. The devices will satisfy the signal handling of 12dB specified by Dolby Laboratories on above voltage range. 2) Operation mode control The CXA1100 series provide fully electronic switching circuits. The functions are controlled by DC voltages of the two control pins of REC/PB (pin 12) and ON/OFF (pin 5). The switching truth tables are shown in Fig. a-2. VH and VL are defined as (a) Single ended supply operation VCC VH 2.5V 0.5V VL 0V (b) Split supply operation VCC VH VEE + 2.5V VEE + 0.5V VL VEE REC/PB Function VH VL
PB (Decode) REC (Encode)
ON/OFF Function
VH NR off Fig. a-2.
VL NR on
It is desirable to provide CR time constant circuits at the mode control pins with time constant from 100msec to 1sec, which will reduce switching clicks effectively. 3) Reference levels Characteristics and specifications of the Dolby noise reduction processor are defined as the levels and measured with reference to the Dolby level. This particular level in these devices is -10dBm (245mVrms), and is measured at the recording output (REC OUT) in the NR off mode. The reference levels of the recording input (REC IN), play back input (PB IN) and line output (LINE OUT) are defined the levels which provide the Dolby level at the recording output in the NR off mode. The CXA1100 series has a common silicon die, and has different internal connection. The series provides four different line output levels for various applications. Other reference levels, recording input level, playback input level and recording output level (= Dolby level) are identical in all devices. The reference levels are as follows Recording output level (= Dolby level) Recording input level Play back input level Line output level CXA1100 CXA1101 CXA1102 CXA1163
-10dBm -30dBm -30dBm 0dBm -3dBm -6dBm -10dBm
(245mVrms) (24.5mVrms) (24.5mVrms) (775mVrms) (548mVrms) (388mVrms) (245mVrms)
- 11 -
CXA1100/CXA1101/CXA1102/CXA1163
4) MPX filter termination and C1 for Vcc/2 (Pin 4) The MPX (multiplex) filter termination method shown in Fig. a-3 allows saving the coupling capacitors between the buffer amplifiers and MPX filters. However, the channel to channel separation and REC to PB crosstalk of low frequency signals will be degraded by the termination resistor RT. For example, 5k of R1 will degrade the channel to channel separation to 50dB. Better separation can be obtained by increasing the capacitance of C1 (Pin 4) to 220F or 470F. The allowable minimum value of C1 is 47F, and 100F is the standard recommended value. Larger values of C1 are generally desirable in order to improve the crosstalk and ripple rejection ratio. 5) Application for dubbing cassette decks The CXA1100 series generates non decoded signal at the recoding output in the decode mode, and can simplify the structure of dubbing decks. See the SONY' Dolby B/C type IC (CX20187/CXA1097Q or CX20188/CXA1098Q) data sheet in detail.
C11 4.7 MPX Buffer Filter MPX Filter RT 16 15 14 13
Line Input
CXA1100 Series
RT Line Input MPX Buffer Filter MPX Filter
1
2
3
4
C21 4.7
C1 470
Fig. a-3. Switchable Processor with Single Supply
C3 10 C14 4.7 LINE OUT C13 (10%) 0.68 11 10 9 C15 4.7
REC PB IN (-30dBm) REC IN (-30dBm) PB C12 1 C11 1 RT RT
REC/PB R2 10k R1 (12 %) 43k 13 12
REC OUT
16
15
14
VCC
1
2
3
4
5 C1 100
6
7
8
C25 4.7
REC IN (-30dBm) PB IN (-30dBm)
C21 1 C22 1
C2 100
C23 (10%) 0.68 NR ON/OFF C24 4.7
REC OUT (-10dBm) LINE OUT
OFF ON
Note 1) Resistor and capacitor tolerances are 10% and 20% respectively unless otherwise specified. Note 2) When resistors RT are connected to Pin 4 for the MPX filter termination, increase the capacitances of C1 and C11 (C21) to 470F and 4.7F respectively. - 12 -
CXA1100/CXA1101/CXA1102/CXA1163
Switchable Processor with Split Supply
REC/PB R2 10k C3 10 R1 (12 %) 43k 16 15 14 13 12 11 10 C14 4.7 LINE OUT C13 (10%) 0.68 C15 4.7 REC OUT (-10dBm)
PB REC PB IN (-30dBm) REC IN (-30dBm) VEE C1 100
C12 1 C11 1
9
C2 100 VCC REC IN (-30dBm) PB IN (-30dBm) C21 1 C22 1
1
2
3
4
5
6
7
8
C25 4.7 REC OUT (-10dBm) LINE OUT
NR ON/OFF ON
C23 (10%) 0.68 C24 4.7 OFF
Note 1) Resistor and capacitor tolerances are 10% and 20% respectively unless otherwise specified.
Playback Processor with AUX input
AUX TAPE IN (-30dBm) AUX IN (-30dBm)
TAPE/AUX
TAPE C12 1 C11 1 16 15 14
R2 C3 10k 10 R1 (2%) 43k 13 12 11 10
C14 4.7 LINE OUT C13 (10%) 0.68 9
VCC 1 C21 1 C22 1 2 3 4 5 C1 100 NR ON/OFF OFF ON 6 7 8 C13 (10%) 0.68 LINE OUT C24 4.7
AUX IN (-30dBm) TAPE IN (-30dBm)
C2 100
Note 1) Resistor and capacitor tolerances are 10% and 20% respectively unless otherwise specified. Note 2) When AUX inputs are not necessary, reject R2, C3, C11, C21 and TAPE/AUX switch, and connect Pin 12 to Vcc. - 13 -
CXA1100/CXA1101/CXA1102/CXA1163
Package Outline
Unit: mm
CXA1101P, CXA1101P CXA1102P, CXA1163P
16PIN DIP (PLASTIC) 300mil
16PIN DIP (PLASTIC) 300mil
+ 0.1 0.05 0.25 -
+ 0.1 0.05 0.25 -
+ 0.3 6.4 - 0.1
+ 0.4 19.2 - 0.1
16
9 7.62
+ 0.3 6.4 - 0.1
+ 0.4 19.1 - 0.1
16
9 7.62 0 to 15 1 2.54 8
0 to 15
1 2.54
8
0.5 MIN + 0.4 3.7 - 0.1 0.5 MIN 0.46 0.1 3.0 MIN 1.53 0.15 3.0 MIN
+ 0.4 3.7 - 0.1
0.5 0.1 1.2 0.15
PACKAGE STRUCTURE
PACKAGE MATERIAL SONY CODE EIAJ CODE DIP-16P-03 DIP016-P-0300-B Similar to MO-001-AE LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY RESIN SOLDER PLATING COPPER / 42 ALLOY 1.0g
PACKAGE STRUCTURE
JEDEC CODE PACKAGE MATERIAL SONY CODE EIAJ CODE JEDEC CODE DIP-16P-01 DIP016-P-0300-A Similar to MO-001-AE LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY RESIN SOLDER PLATING COPPER 1.0 g
CXA1101M, CXA1102M CXA1163M
16PIN SOP (PLASTIC) 300mil
CXA1100P, CXA1101P CXA1102P
16PIN DIP (PLASTIC) 300mil
19.35 0.5 16 9 0.15 + 0.2 0.1 - 0.05 6.9 16 9 7.62
6.35 0.127
+ 0.1 0.28 - 0.06
+ 0.4 9.9 - 0.1
+ 0.4 1.85 - 0.15
0 to 10
+ 0.3 5.3 - 0.1
7.9 0.4
1
8 2.54 0.254
0.45 0.1
1.27
+ 0.1 0.2 - 0.05
0.5 0.2
1
8
0.508 MIN 3.1 MIN
1.016
0.12 M
0.457 0.076
PACKAGE STRUCTURE
PACKAGE MATERIAL SONY CODE EIAJ CODE JEDEC CODE PACKAGE WEIGHT SOP-16P-L01 SOP016-P-0300-A LEAD TREATMENT LEAD MATERIAL EPOXY RESIN SOLDER PLATING SONY CODE COPPER ALLOY EIAJ CODE JEDEC CODE DIP-16P-191 DIP016-P-0300-AU MS-001-AA
5.08 MAX
PACKAGE STRUCTURE
PACKAGE MATERIAL LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY RESIN SOLDER PLATING COPPER 1.0g
0.2g
- 14 -
CXA1100/CXA1101/CXA1102/CXA1163
CXA1100P, CXA1101P/M, CXA1102P/M, CXA1163P/M
16PIN SOP (PLASTIC) 300mil
+ 0.3 10.2 - 0.1 16 9
2.0 MAX
0.05 MIN
+ 0.3 5.3 - 0.1
7.8 0.1
1.8
1 0.71 0.1 1.27 0.1 0.4 0.1
8
0.15 0.05
0.13 M
0.15
4 to 8
NOTE: Dimension "" does not include mold protrusion.
PACKAGE STRUCTURE
PACKAGE MATERIAL SONY CODE EIAJ CODE JEDEC CODE SOP-16P-L122 SOP016-P-0300-BX LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY RESIN SOLDER PLATING COPPER 0.21g
- 15 -
0.75 0.2

▲Up To Search▲

Price & Availability of CXA1100

	To Download CXA1100 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .